Greenville Electrical Company handles electrical work for homes and businesses across Greenville and the surrounding communities. Whether the job is a straightforward outlet repair or a full panel upgrade ahead of a major renovation, we cover the full range of residential and commercial electrical work. Real experience. Local knowledge. Ready to wire.
We work with property owners, contractors, and business operators who need electrical problems solved without the back-and-forth. The scope is clear before anything is scheduled, the price is confirmed on the call, and the work is done to the standards that Greenville County inspectors enforce.
Getting your power back is easier than you think. Most of the calls we get fall into a handful of familiar patterns: lights flickering in one room, an outlet that stopped working, a breaker that trips every time a certain appliance runs, or half the house going dark without an obvious cause. Each of those symptoms points somewhere specific, and a visit is built around finding that point.
Flickering lights can mean a loose connection at the fixture, a failing breaker, or a problem further back in the circuit. Dead outlets are often a tripped GFCI somewhere upstream, but they can also be a wiring fault that needs tracing. A breaker that keeps tripping is telling you the circuit is being asked to carry more than it was designed for, or that something in the wiring is wrong. We get to the bottom of the problem fast.
We take short-notice calls for urgent electrical faults. If something is wrong with the power in your home or business, reaching us is the first step.
This area has every kind of panel and circuit in it, from older 100-amp services in homes that were built long before modern electrical loads existed, to commercial setups that need a subpanel to feed a new wing or workshop. When a panel can no longer handle what the property demands, the work involves replacing the breaker panel, upgrading the service entrance, and in some cases replacing the meter base.
A 200-amp service upgrade is one of the most common jobs we handle in Greenville. Older homes running on 100-amp service often hit a wall when homeowners add an EV charger, a larger HVAC unit, or a second refrigerator in the garage. A load calculation tells us what the panel needs to carry, and the upgrade is scoped from there. Subpanel installation follows the same logic: when one panel cannot reach every part of a larger property, a subpanel brings capacity to where the work is being done. We show up ready to wire, whatever the panel configuration requires.
Greenville's housing stock covers a wide range of ages and construction types. Older neighborhoods closer to downtown often have original wiring that was adequate for its time but was never designed to carry today's loads. Knob-and-tube wiring, aluminum branch circuit wiring, and panels with fuse blocks rather than breakers all turn up regularly in this area, and each one involves different considerations when it comes to repairs, additions, or full rewiring.
Newer construction in the outer parts of Greenville County tends to be wired to more recent code, but additions and renovations on those homes still need to tie into existing circuits correctly. A basement circuit for a sump pump, a dedicated line for a chest freezer, or new wiring for a finished room all have to be planned around what the panel can support and what the code requires. Knowing what is common in this area's homes changes how a job is scoped from the first call.
Whether this is your first repair or your tenth, the wiring behind it matters as much as the fix in front of you. Whole-home rewiring comes up most often in older Greenville properties where the original wiring can no longer carry modern loads safely or where an inspection has flagged it as a concern. We also handle wiring for renovations, room additions, garages, and basements, where new circuits have to be run and tied into the panel correctly.
Code-compliant wiring means GFCI protection in kitchens, bathrooms, garages, and outdoor areas, and AFCI protection on bedroom circuits, among other requirements. Arc-fault and ground-fault breakers are part of that picture, as is proper grounding and bonding throughout the system. We take pride in the electrical work we leave behind, and that means every installation meets the current code, not just the minimum that gets it to pass.
Homes and businesses need different wiring answers, but the everyday installation work follows a familiar list. Outlet installation and replacement, GFCI outlet upgrades in wet areas, dimmer switches, recessed lighting, LED retrofits, exterior and security lighting, and ceiling fan installation and wiring all fall within what we handle on a regular basis.
For homeowners, a lot of this work comes up during a remodel or when something stops working and turns out to need more than a bulb change. Recessed lighting in a living room, a new outdoor fixture over a garage door, or a ceiling fan in a bedroom that was never wired for one: each job involves running wire, connecting at the panel if a new circuit is needed, and finishing the installation correctly. Call us and the rest is handled.
Greenville is seeing steady demand for EV charger installation, and it is easy to understand why. A Level 2 home EV charger needs a dedicated 240-volt circuit, and in many cases the panel has to be assessed before that circuit can be added. We handle the wiring from the panel to the charger location, confirm the panel has capacity for the load, and install the circuit to code.
Dedicated appliance circuits follow the same principle. A dryer, a range, a refrigerator in the garage, or a chest freezer all benefit from a circuit that is not shared with anything else. Whole-home surge protection is a separate installation at the panel level that guards the entire electrical system against voltage spikes, including those that come in through the service entrance after a storm. Power restored. Code-compliant. Done right.
Backup generator hookups involve a transfer switch, which is the component that safely disconnects the home from the utility grid before the generator takes over. Without it, a generator feeding power back into the grid is a hazard for anyone working on the lines. We install the transfer switch, connect it to the panel, and wire the generator inlet so the hookup is safe and correct.
Electrical safety inspections cover the panel, the wiring, the outlets, and the grounding system. They are useful before buying an older home, after storm damage, or when something has been flagged during a sale. Hardwired smoke detector and carbon monoxide detector installation also falls under this category, and we can wire those into the system during the same visit. We'll get your lights back on fast, and we will make sure everything feeding them is in order.
We cover Greenville and the communities throughout Greenville County, including Simpsonville, Mauldin, Taylors, Greer, Fountain Inn, and Travelers Rest. Whether the job is in a neighborhood close to downtown or further out toward the county line, calls about any of these locations are answered here.
The person who answers the phone can tell you what the visit involves. That means you know what is included before anything is scheduled, and you can ask about availability, what the job covers, and what to expect on the day. We are available every day from 9:00 AM to 8:30 PM, and we take short-notice calls for urgent electrical faults during those hours.
The scope and the price are settled on the call. When you reach us about a job, we ask enough questions to understand what is involved, and we confirm the price before anything is booked. That number covers what we discussed, and the same number you called to book the job is the number to call if you have questions afterward.
We do not schedule work and figure out the details later. Straight answers about your panel and wiring are part of every call, so you go into the job knowing what it involves and what it costs. Call and we'll get you back to full power.
The cost of electrical work varies by job type, and the only way to give you an accurate number is to understand what the job involves. When you call, we ask about the symptom, the property type, and what has already been checked. From there, we give you a price that reflects the actual scope.
You get the rate on the phone, before anything is scheduled, and you are told what it covers. If the job turns out to involve something that was not visible on the call, that is a conversation before the work continues. Ask what the price covers and you get a straight answer.
We work with homeowners, renters, landlords, property managers, contractors, and business operators across Greenville and Greenville County. The work ranges from a single outlet repair in a rental unit to a full panel upgrade ahead of a commercial build-out, and we handle both ends of that range.
A small job like a dead outlet or a tripping breaker gets scoped on the call and handled in a single visit. A larger job like a whole-home rewire or a service upgrade involves more questions upfront, a load calculation in some cases, and a fuller picture of what the property needs before anything is scheduled. The process is the same either way: scope first, price confirmed, then work begins.
Greenville's housing stock covers a wide range of ages, and older neighborhoods closer to downtown frequently turn up knob-and-tube wiring, aluminum branch circuit wiring, and panels with fuse blocks rather than breakers. We handle all of those, and knowing what is common in this area's homes changes how a job is scoped from the first call.
When you call, you reach someone who knows the trade and can scope the job from your description. The work at the property is carried out by people who know what the job involves and what the code requires in Greenville County. We confirm what the visit covers before anyone is sent out.
Before we leave, the work is tested and confirmed to be functioning correctly. For panel work, that means verifying the circuits are live and the breakers are operating as expected. For outlet and wiring work, we test the device and check that the circuit is behaving correctly under load.
Clear access to the panel, the work areas, and any outlets or fixtures involved makes a real difference. On the call, we ask about the layout and flag anything that might affect the visit. A job where the scope is understood on both sides before anyone arrives tends to run without delays.
Call us and we will work through what happened. The conversation starts on the phone, where we ask about the symptom and figure out whether it is related to the original work or something new. We do not leave a problem unaddressed.
The same symptom, a tripping breaker for example, can point to a failing breaker, an overloaded circuit, a wiring fault, or a combination of all three. The repair depends on what the fault-finding turns up, not just what the symptom looks like on the surface. That is why we scope the job from the symptom back to the source before quoting the fix.
Greenville Electrical Company handles the full range of electrical work for homes and businesses in Greenville, South Carolina, and across Greenville County. From a tripped breaker to a full panel upgrade, from a single outlet to whole-home rewiring, we scope the job on the call and get it scheduled. Schedule it. We wire it. You're powered.
Call (864) 365-3623 to get a quote or book a service call. We are available every day from 9:00 AM to 8:30 PM.
(864) 365-3623